Schluter KERDI-BOARD
Schluter KERDI-BOARD is a lightweight, waterproof foam building panel that gives tile a flat, stable base. This collection holds every flat KERDI-BOARD panel we carry: 48" x 96" sheets in 3/16", 3/8", 1/2" and 5/8", a 5/8" x 48" x 120" sheet, smaller 48" x 64" and 48" x 32" formats, and 24-1/2" x 96" panels from 3/4" to 2" thick. Choose a thin panel where it will be fully supported, and a thick panel for a countertop or a partition wall.
Frequently asked questions
See all FAQsWhat sizes and thicknesses does Schluter KERDI-BOARD come in?
Flat KERDI-BOARD panels come in eight thicknesses: 3/16" (5 mm), 3/8" (9 mm), 1/2" (12.5 mm), 5/8" (15 mm), 3/4" (19 mm), 1" (25 mm), 1-1/2" (38 mm) and 2" (50 mm). We carry 48" x 96" (4 x 8 ft) sheets in 3/16", 3/8", 1/2" and 5/8", a 5/8" x 48" x 120" sheet, 48" x 64" sheets in 3/16", 3/8" and 1/2", a compact 1/2" x 48" x 32" panel, and 24-1/2" x 96" panels in 3/4", 1", 1-1/2" and 2". For a full 4 x 8 ft sheet, see the 1/2" x 48" x 96" KERDI-BOARD.
Which KERDI-BOARD thickness do I need for a tiled countertop?
Schluter calls for KERDI-BOARD at least 1-1/2" (38 mm) thick for countertops. The panels are adhered directly to the base cabinets with KERDI-FIX adhesive, and every panel joint is sealed with KERDI-FIX or thin-set mortar. Shop the 1-1/2" x 24-1/2" x 96" KERDI-BOARD, and finish exposed edges with Schluter finishing profiles.
Can I build a partition wall or shelving with KERDI-BOARD?
Yes, for non-bearing builds. For a partition wall, Schluter calls for KERDI-BOARD at least 2" (50 mm) thick, adhered to the permanent wall for lateral stability, with the panel joints sealed with thin-set mortar or KERDI-FIX. These partition walls are not load-bearing. For shelving, panels from 3/4" (19 mm) thick may be used, checked against your building specifications. See the 2" x 24-1/2" x 96" KERDI-BOARD.
Can KERDI-BOARD go over an existing wall or masonry?
Yes. KERDI-BOARD can be installed over masonry and finished wall surfaces. If the wall is even and plumb, any thickness can be fully embedded in thin-set mortar; the 3/16" KERDI-BOARD is the thinnest option. To correct an uneven wall, spot-bond panels at least 3/8" (9 mm) thick, such as the 3/8" x 48" x 96" KERDI-BOARD, with spots of thin-set about 12" (30 cm) apart.
Does KERDI-BOARD add insulation value?
Yes. The foam core adds thermal resistance. Schluter lists R 0.9 for 3/16" (5 mm), R 2.2 for 1/2" (12.5 mm) and R 9.1 for 2" (50 mm), tested to ASTM C518. Other thicknesses fall between these values, but Schluter does not publish a figure for each one. The thickest panel, the 2" KERDI-BOARD, gives the highest value.
Can KERDI-BOARD be used outdoors, and how should I store it?
No. KERDI-BOARD is made for interior applications only. Store the panels flat. If they must sit outside before installation, protect them from direct sunlight and weather. For help choosing panels for your project, contact us.
Can’t find your answer?
Browse the general FAQ, chat with a flooring specialist or send us a message.